At that point, you might as well go all the way to support a TMC4361 to get real closed loop working.I wish there was a mode of marlin to offload the ramp generator to another microcontroller. Please keep us updated! Get the quality you expect from Avery, the world’s largest supplier of labels. Based on Trinamic's sophisticated SpreadCycle™ and StealthChop™ choppers, it ensures absolutely noiseless operation combined with maximum efficiency and best motor torque. Here’s a link: By the way, WarlockD, have you been experimenting with Marlin 2.0 software for 3D printers? i saw that you wrote some functions for setting the RMS current of 5160 and i was worried that it was somehow different.
Hi doods and dudettes, Been thinking of switching to the SKR 32bit board because i dunno whatever
Here are the few steps required to get started. This graphical user interface allows quick setup and supports the use of commands in direct mode, monitors real-time behavior visualized in graphs, and logs and stores data.
TMC has some pictures of the TMC2160 (same as the TMC5160, just no ramp generator), in that format but there doesn't seem to be anyone making them.I think there is just such a glut of TMC2130 and older chips that no one is trying to make them in bulk. it could also run a web server for host.You can try disabling the monitoring feature as then there will be no periodic communication to the drivers.I mean in the TMCStepper Lib is there a way to reduce the SPI traffic?If you have monitoring disabled then there is no SPI calls made after initial reboot.Successfully merging a pull request may close this issue. I also would like to run the TMC5130A BOB and TMC5161 BOB to compare the results and behavior, so any suggestions on how to do this with the same relative code is appreciated, but 1st I need to get the TMC-5160 working!! I saw you added support for 5160 and i was wondering if the differences are big and weather the code for 2130 could work for at least basic setup of 5160. im wondering because smoothieware is about to get support for 2130 but 5160 is probably way of.The 5160 brings the advantages from each of the previous ones together and it will definitely be the best driver available.Depending on the pricing and availability, I'd probably never recommend any of the other models anymore.The good news is that it shares a lot with 2130 and you'll likely be able to use them by defining them as 2130 drivers.that really is good news.
SilentStepStick.
The TMC5160 is a high power stepper motor controller and driver IC with serial communication interfaces. For diagnosis, all signals between MCU and TMC5161 are accessible with probes on the Eselsbrücke bridge board. It allows for a quick and simple start within only minutes to make your motor turning, while still providing full access to all registers and full functionality and diagnostics. Going to buy the new SKR 1.3 board which will be a pretty good upgrade from my current motherboard which has built in stepper driversPlease share how was your experience with the SKR 1.3 and the TMC 5160,Will do! at high current the mosfets would need cooling as well. BIGTREETECH DIRECT TMC5160 V1.2 SPI Stepper Motor Driver 4.4A High Power Mute Driver 3D Printer Parts for SKR V1.3 PRO Control Board VS TMC2130 SPI 4.7 out of 5 stars 31 $58.98 3.0 (6) 10 Orders.
One of the best premium level shocks available for truck and Jeep platforms, these last an incredibly long time with exceptional handling in most terrains.When performance offroad, or under heavy duties is the primary concern or purpose of the rig, these may be a better option. Stepper Motor Driver based on a Trinamic TMC2100 / TMC2130 / TMC2208 / TMC2209 / TMC5160 / TMC5161. 5160-Carbon 0.56 - 0.64 Chromium 0.7 - 0.9 Manganese 0.75 - 1 Phosphorus 0.035 max Silicon 0.15 - 0.35 Sulphur 0.04 max 1060-Carbon 0.55 - 0.65 Manganese 0.6 - 0.9 Phosphorus 0.04 max Sulphur 0.05 max 1060 is a simple carbon steel, and 5160 is considered an alloy steel. while these allow much higher current handling they complicate the design. They have the mosfets on the board so it’s just plug and play as far as I can see. Just checking. 5160 vs 5100's.
Been mulling over whether I should go with the TMC5160 (higher amps), or the TMC2209 (newer/more advanced versions of older features).
The Silent-Step-Stick is a Stepper Motor Driver Board for 2-Phase Motors, based on Trinamic Drivers: TMC 2100 / TMC 2130 / TMC 2208 / TMC 2209 / TMC 5160 / TMC 5161. All you need to get started is a power supply and Trinamic's free and easy to use TMCL-IDE. Only a few wires including an SPI port are required to control TMC5130-EVAL with your Arduino.